Wednesday, April 14, 2010

What's the Point?

There is very little standardization in the way saddles fit - particularly when it comes to width.  Tree construction varies from company to company, so one company's medium may be comparable to another company's medium-wide or wide.  Trees made in the UK to BETA (British Equestrian Trade Ass'n.) standards have to be within a certain angle measurement - a medium, for example, between 85° and 94.9°, and a wide between 95° and 104.9° - but that's almost 10° variation.  Even centimeter measurements, which you'd think would be a more exacting way of measuring width, aren't much help.  A 29 cm. Passier (that company's x-wide tree) will fit a wider horse than a 32 cm. Stubben. 

Why?  Tree point length.  Saddles measured in centimeters are measured between the tree points on the bare tree, before the saddle is built.  So if you have an 8" long point, 32 cm. will be considerably less generous than if the points are 5" long.  To illustrate, I've compared a 28.5 cm. "wide" Passier with an "xw" Stubben (which, according to Stubben's web site, is wider than a 32 cm., though no exact width measurement is listed).

Here's the Passier.  Edie's index finger is showing the location of the bottom of the tree point:

Measured from the saddle nail down to the end of the point, it's just about 5":

Now, here's the Stubben, with Edie's index finger again at the end of the tree point:



And here's the length of the point - about 8":



Here's a comparison of the same saddles (remember, Stubben xw, Passier wide, 28.5 cm.) from the front, with the ends of the tree points marked with tape.  First, the Passier:

 

Though it's hard to see, the measurement is just under 12".

Here's the Stubben:


Again, hard to see the numbers, but it's measuring about 12 1/2".

The longer points on the Stubben can be helpful when fitting a horse with a good wither - they distribute the weight all the way down the wither.  But on a horse with moderate to no wither, long points can make the saddle "perch" and cause lateral instability.

And when you add panel configuration and tree shape into the mix, it can be even more confusing.  A K panel or a wither (or full front) gusset will make a saddle fit less generously.  A hoop / freedom head tree or a panel that's attached lower down in the gullet (like Passier's Freedom panel) will make a saddle more generous in the width department.   Here's a photo with three saddles - all 34 cm. trees - so you can see the variation in width.  The top saddle is a Duett Largo, built on a hoop-type tree; the middle is a Prestige 2000D, and the bottom saddle is a Duett Fidelio.


And to get an idea of how panel configuration figures in, here are two Black Country saddles - an Eloquence X on top, and a Vinici X on bottom.  Both are 17.5" wides, built on the same tree ... but look at the difference.


So if you're in the market for a saddle, remember that describing your horse as needing a "wide" tree or a "33 cm. tree" can be open to a LOT of interpretation.

6 comments:

  1. I completly understand this blog. I have bought 3 saddles within the space of a week, all apparently a wide fitting, varying from 7" to 9" D-D but the flocking in each varied so much that none fit and I'm still searching for one that meets all the fitting criteria.

    ReplyDelete
  2. Thankyou! You are probably the only one who's actually explained all this tree size. It's confusing!

    ReplyDelete
  3. Now I'm even more confused... It looks like there is no way one can just pick a saddle without a saddle fitter and a bunch of different saddles! But thanks a lot for this article!!

    ReplyDelete
  4. Working with a good fitter really is the best way to find the right saddle, Anon. - and be sure you have a FITTER rather than just a REP. While I know some reps who are excellent fitters, I also know some reps who have had very little training in actual fitting, though they can sell faster than a horse can trot!

    ReplyDelete
  5. What to do with a lop sidded horse with a big shoulder muscle. Really lop sided I have cut a raiser pad to remove the raise on the side the mare is / and to raise the saddle on the hollow side : the shape is more like the side of a fiddle(?) hope this helps. Added to this she has a short back and a very small girth space. Maybe driving is in her future.

    ReplyDelete
  6. Anon, I can't offer much input w/o seeing the issue in question, sorry, but I can say that shim pads can be a big help in working through asymmetries. Good training, shoeing, chiropractic and dental all come into play here, so being sure all of those things are addressed will be a help as well. Please feel free to email me some photos if you'd like - the address is pantherrunsaddlery@yahoo.com.

    ReplyDelete